If you have an Intex pool, you may need to drain it at some point. Here’s how to do it: First, remove the pump and any other attachments. Then, open the drain plug and let the water start draining out. You can use a garden hose to direct the water away from your home if necessary. Once the water level is low enough, you can start dismantling the pool itself.
Take down the walls and then fold up the liner so that it can be easily removed. Drain any remaining water out of the liner before taking it off completely.
- Locate the drain plug on the pool wall and unscrew it
- Place a garden hose over the drain hole and secure it with a rubber band or tape
- Turn on the water supply and allow the water to flow out of the pool until it is completely empty
- Once the pool is empty, remove the garden hose and screw the drain plug back into place
How to Drain Intex Pool With Garden Hose
If you have an Intex pool and need to drain it, there are a few things you’ll need to do first. Make sure all the plugs are removed from the bottom of the pool so that water can start draining out. Next, attach your garden hose to the drainage spout on the side of the pool.
Once everything is hooked up, open up the valve on the drainage spout and let the water begin draining out into your yard or wherever you’re directing it. Drainage should happen pretty quickly since gravity will be working in your favor. Just make sure to keep an eye on things and move your hose around if needed so that all areas of the pool are draining evenly.
Once most of the water is gone, you can close off the valve and remove everything. Give your pool a good cleaning before refilling it so that it’s ready for use again. And that’s all there is to draining an Intex pool with a garden hose!
How to Drain Intex Pool Without Adapter
If you have an Intex pool and need to drain it, you can do so without the adapter. All you need is a garden hose and a way to connect it to the drainage hole in the bottom of the pool. To start, lower the water level in the pool as much as possible.
Then, remove any plugs or fittings that are blocking the drainage hole. Once those are removed, simply attach your garden hose to the drainage hole and turn on the water. The pool will start draining immediately.
You may want to position the hose so that the water drains away from your house or other structures. Also, be sure to keep an eye on the water level in the pool so that it doesn’t get too low and cause damage to the liner. Once all of the water has been drained from your Intex pool, simply remove the hose and put everything back in place.
Then you’re ready to fill up your pool again and enjoy!
How to Drain Intex Pool With Pump
Are you the proud owner of an Intex pool? If so, congratulations! You’ve made a great investment in your family’s summer fun.
But like all pools, your Intex pool will need to be drained and refilled from time to time. This can be a big job, but with the right pump it doesn’t have to be too difficult. Here’s a step by step guide to draining your Intex pool with a pump:
- 1. Disconnect the hoses from the skimmer and return jets. If your Intex pool has an auto-skimmer, you’ll need to remove that as well.
- 2. Place your submersible drain pump at the deepest point in the pool, making sure that the discharge hose is pointing uphill.
- 3. Plug in the pump and turn it on. The water will start flowing out of your pool and into whatever container you have placed under the discharge hose (a kiddie pool works great for this).
- 4. Once the water level has dropped significantly, you can move the pump to shallower areas of the pool until it is completely empty.
- 5. Once the pool is empty, disconnect and store your drain pump according to its instructions.
Intex Pool Drain Adapter
If you have an Intex pool, you know that they are a great way to enjoy the summer without having to deal with the hassle and expense of a traditional in-ground pool. One thing you do need to be aware of, however, is that Intex pools require a special drain adapter in order to properly drain the water.
Without this adapter, your pool will not drain properly and could lead to costly repairs.
The good news is that the adapter is relatively inexpensive and easy to install. Simply attach it to your garden hose and insert it into the drain plug on your pool. Once it’s secure, turn on the water and watch as your pool quickly drains away.
How to Drain Bestway Pool Without Adapter
If you have a Bestway pool, you may be wondering how to drain it without an adapter. Here are some simple instructions:
1. First, locate the valve at the bottom of the pool.
This is usually located near the drain plug.
2. Next, use a wrench or pliers to loosen the valve so that water can begin to flow out.
3. Once the water has begun draining, remove the drain plug from the pool and allow all of the water to empty out.
4. Finally, replace the drain plug and tighten it securely before inflating your pool again.
How Long to Drain Intex Pool
If you have an Intex above ground pool, you may be wondering how long you need to drain the pool before you can start using it again. The answer depends on a few factors, including the size of your pool and the weather conditions.
In general, it is best to wait at least 24 hours after draining your pool before refilling it.
This gives the liner time to dry out and prevents any mold or mildew from forming. If it is particularly hot and humid outside, you may want to wait even longer before refilling your pool.
Once you have drained your pool, be sure to clean it thoroughly before refillings.
Pay special attention to the area where the waterline was as this is where most of the dirt and grime will accumulate. A good scrub with a stiff brush should do the trick!
How to Drain Intex Rectangular Pool
If you have an Intex rectangular pool, you may need to drain it at some point. Here’s how to do it:
- 1. First, remove any accessories or ladder from the pool.
- 2. Next, locate the drain plug on the bottom of the pool liner.
- 3. Use a garden hose to attach to the drain plug and secure with a clamp.
- 4. Turn on the water and let it run until the pool is completely drained.
- 5. Once drained, remove the hose and clamp and replace the drain plug in the bottom of the liner.
How Do I Drain My Intex Pool Without a Pump?
If you have an Intex pool and don’t have a pump, there are still ways that you can drain your pool. One way is to use a garden hose. Attach the hose to the drainage plug on the side of the pool.
Turn on the water and let it run until the pool is empty.
Another way to drain your Intex pool without a pump is to use a submersible pump. These pumps are designed to be placed underwater and can be used to quickly drain your pool.
Finally, you can also use gravity to help drain your Intex pool. If your pool is on an incline, open up all of the drains on the bottom of the pool so that gravity can pull the water out.
How Do I Drain My Intex Pool for the Winter?
Assuming you have an above ground Intex pool, there are a few things you need to do in order to properly drain it for the winter.
First, you’ll want to remove all of the accessories from your pool – this includes ladders, hoses, pumps, and any other attachments. Once everything is detached, you can begin draining the water.
To do this, locate the valve at the bottom of your pool (it should be near where the hose attaches) and turn it to the “drain” setting. Then, attach a garden hose to the valve and run it away from your pool area – make sure that wherever you’re draining the water won’t cause any flooding or damage!
Once all of the water has been drained out, give your pool a good cleaning before storing it away for the winter.
This will help ensure that it’s in good condition when you go to set it up again next season.
How Do You Drain a above Ground Pool With a Garden Hose?
If you have an above ground pool, chances are you will eventually need to drain it. Whether it’s because the water is too dirty, the liner needs to be replaced, or you simply want to empty it out, draining an above ground pool can be done relatively easily with a garden hose.
To start, you’ll need to remove any accessories from your pool, such as ladders, diving boards, etc.
Next, lower the water level in your pool by using a submersible pump to remove water from the deepest part of the pool. Once the water level is low enough, disconnect any hoses or other attachments that are keeping your pool full.
Now it’s time to begin draining the water out of your pool.
The easiest way to do this is by attaching a garden hose to the drain valve at the bottom of your pool and running the hose away from the pool and into a nearby drainage area. If your garden hose doesn’t fit snugly onto the valve, you can try using duct tape or another type of sealant around the connection point to prevent leaks. Once everything is secure, open up the valve and let gravity do its job!
Depending on how much water is in your pool, it may take some time for all of it to drain out. You can speed up this process by adding more hoses or even positioning a fan near the end of your drainage hose to help move things along quicker. Just be sure not to leave yourpool unattended while draining – if something wereto go wrong (like a broken hose), you could end up with quite a mess onyour hands!
How to DRAIN Your Intex EasySet Pool
Conclusion
If you have an Intex pool, you may need to drain it at some point. Here’s how to do it:
First, remove any accessories from the pool.
This includes ladders, slides, etc.
Next, use a garden hose to attach to the drain plug at the bottom of the pool. Make sure the hose is long enough to reach a drainage area such as a storm drain or sewer cleanout.
Once the hose is attached, open the drain plug and let the water start draining out. You may want to use a submersible pump to help speed up the process.
Once the water is completely drained, remove the hose and close the drain plug.
Your pool is now ready for storage or winterization.
1 thought on “How to Drain an Intex Pool”